Trend TREKWJ700 Kitchen Worktop Jigs

The Trend Kitchen Worktop Jig is a hard-wearing solid laminate, 12mm thick jig that enables cutting both parts of the joint in 15 minutes including setting up. The jig has the following features: Left and right hand corners, 400mm radius peninsular joint, 45° end cut with slight radius, 45° trade corner, 40mm radius corner, 35mm kitchen door hole and 3/4inch BSP hole for mixer taps....

Trend TRESNAPDBG5 Snap Centring Guides

These spring loaded drill bit guides are self centring and are used for accurate drilling of holes for fittings such as hinges to ensure exact alignment. They can be easily dismantled for cleaning and are supplied with a HSS Drill Bit.

Trend TRECSB1653PB CraftPro Cordless Saw Blade Triple Pack

Trend CraftPro Cordless Saw Blade, designed for a professional finish in softwood, hardwood, plasterboard, stone fibreboard, particle board, veneer, plywood, MDF and hardboard. Thin kerf, ideal for cordless saws. High-grade alloy steel plate body precision ground to maintain flatness. Silver brazed to ensure tips are securely bonded to body. With a reamed bore to ensure a precise spindle fit. Laser etched on reverse to European...

Trend TRECSB1603P CraftPro Plunge Saw Blade

The Trend CraftPro Plunge Saw Blade is designed to provide a professional finish in particleboard, plywood, MDF and hardboard. It has a high-grade, hardened and tempered, alloy steel plate body which has been precision ground to maintain flatness. Silver brazed to ensure tips are securely bonded to the body, and with a reamed bore to ensure a precise spindle fit. Laser-etched on the reverse to...

Trend TREC15212TC Biscuit Jointer Set, Craft Pro

This TCT two wing slotting cutter is ideal for biscuit jointing sizes The set is supplied with 3 ball bearing guides to suit the three sizes of biscuits available. A slighlty longer cut than the length of the biscuit is required for ease of alignment during assembly Supplied with instructions. No. 0 - 45 mm x 15 mm x 4 mm Suitable for 8-12 mm...

Trend TREC07814TC CraftPro Round Over Two Flute Cutter, 1/4in Shank

The Trend CraftPro Round Over Cutter leaves perfect, superfine, round over detail for a contemporary, eased edge arris profile on straight and curved edges. With two carbide TCT tips for cleaner cutting edges and fast clearance of waste in all timber and timber-based materials. A PTFE coating minimises heat and resin build-up for increased cutter performance and longevity. 1/4in shank for easy control in smaller...

Trend TREAIRPRO Airshield Pro Powered Respirator

The Trend Airshield Pro Respirator is a fully protected powered respirator for use with all woodworking applications and is suitable for use when machining MDF. It is approved to new standard BS EN 12941. New features include:Combination face-seal and hood to improve protection.Motor positioned away from the sensitive area of the forehead to reduce noise and irritation.Attachment points for optional ear defenders.Strategic component distribution ensures...

Trend TREB16 Replacement Bearings

Replacement bearing to suit all Trend bearing guided router cutters. The Bearings are shielded to prevent penetration of dust and grease packed for life and should not be cleaned with solvent or lubricated as this will dissolve the grease and cause premature bearing failure.

Trend TRE63127 Collet Sleeves

Trend collet reduction sleeve, used to reduce the collet size to take cutters with smaller shanks. Should only be used as a stop-gap, as the correct size collet is recommended. Should not be used for extensive periods or heavy work.

Trend TRE469412TC 90° Shank Mounted Template Profiler

Profilers with shank mounted bearings for guidance, for use with router mounted above or below a table when following a template. Bearing guided cutters are suitable for both straight and curved work. For profiling and rebating applications only. NOT for plunge, cutting or grooving. A 3 mm approximate overlap should be left before copy profiling, also when using plastic laminate always allow laminate adhesive to...

Trend TRE463714TC 45° Bearing Guided Chamfer Cutter

These types of cutters are used for edging work and chamfer cutting on man made fibre boards, natural timbers and plastics. Tools are offered to produce various angles for chamfering. Ball bearing and pin guarded cutters enable curved work to be undertaken with bearings running along the board edge or a template. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.

Trend TRE46214TC 90° Template Profiler

Self-guiding cutters with bearings mounted for trimming and bevelling timber, lippings and plastic laminate edges for cabinet making, countertop production or any shaping applications. Bearing guided cutters are suitable for both straight and curved work, bearings are normally fractionally larger than cutter diameter, to avoid surface scoring. Uses:Trimming plastic or plywood overlay.Copy profiling - use the bearing to follow a template or base edge of...

Trend TRE11314HS 45° Chamfer V-Groove Cutter

Chamfer V-grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1.0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.

Toupret TOUTTFIBA02 Tough Multi-filler

Toupret Tough Multi-filler is a versatile all-in-one product for exterior substrates. Its fibre-reinforced formula provides exceptional adhesion and strength. Can be overcoated in 24 hours with any standard water-based masonry paint or mineral paint. If using polyurethane or epoxy solvent-based paints, first prime with a water-based exterior paint. Specifications: Application Method: Manual or Spray Machine.Max. Recommended Application Thickness: 5mm.Min. Recommended Application Thickness: 1.5mm.Working Time: 40...

Thor THORH125 Hide Split Head Hammer

The Thor Hide hammer has split cast iron head with two hide faces fastened securely to the handle with two socket head cap screws. The head design allows quick adjustment or replacement of either the handle or the faces, while the faces are designed to wear and can be rotated for even wear. There are 5 different weights to choose from in this range. For...